Supermicro SYS-5038A-IL Manuel d'utilisateur

®SuperWorkstation5038A-IL SUPERUSER’S MANUAL1.0

SuperWorkstation 5038A-IL User's Manual1-21-2 Serverboard FeaturesAt the heart of the SuperWorkstation 5038A-IL lies the X10SAE, a single process

7-18SuperWorkstation 5038A-IL User's ManualIf the item above - SATA Mode Select is set to IDE, the following items are displayed:Serial ATA Port

Chapter 7: BIOS7-19PCI Latency TimerThis feature sets the latency timer of each PCI device installed on a PCI bus. Select 64 to set the PCI latency to

7-20SuperWorkstation 5038A-IL User's ManualOnboard LAN1/LAN2 Option ROMSelect iSCSI to use the iSCSI Option ROM to boot the computer using an iSC

Chapter 7: BIOS7-21TPM StateSelect Enabled to use TPM (Trusted Platform Module) settings for system data security. The options are Disabled and Enable

7-22SuperWorkstation 5038A-IL User's ManualFirmware Update Confi gurationME FW Image Re-FlashSelect Enable to re-fl ash the ME (Management Engine)

Chapter 7: BIOS7-23Change (Serial Port 1 / Serial Port 2) SettingsThis option specifi es the base I/O port address and the Interrupt Request address of

7-24SuperWorkstation 5038A-IL User's Manual• VDIMM• 5Vcc • PCH 1.05V • AVCC• 3.3Vcc • VSB • VBATSerial Port Console RedirectionCOM1/COM2Use thi

Chapter 7: BIOS7-25ParityA parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is se

7-26SuperWorkstation 5038A-IL User's ManualRedirection After BIOS PostUse this feature to enable or disable legacy console redirection after BIOS

Chapter 7: BIOS7-277-4 Event LogsChange SMBIOS Event Log SettingsEnabling/Disabling OptionsSMBIOS Event LogChange this item to enable or disable all

1-3Chapter 1: Introduction1-3 Chassis FeaturesThe SC732D4F-500B is mid-tower chassis. The following is a general outline of the main features of the c

7-28SuperWorkstation 5038A-IL User's ManualWhen Log is FullSelect Erase Immediately for all messages to be automatically erased from the event l

Chapter 7: BIOS7-297-5 Boot SettingsUse this feature to confi gure Boot Settings:Set Boot PriorityThis option prioritizes the order of bootable devices

7-30SuperWorkstation 5038A-IL User's Manual Delete Boot OptionUse this feature to remove a pre-defi ned boot device from which the system will bo

Chapter 7: BIOS7-317-6 Security SettingsThis menu allows the user to confi gure the following security settings for the system.Main Advanced SecurityBo

7-32SuperWorkstation 5038A-IL User's Manual7-7 Save & ExitSelect the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setu

Chapter 7: BIOS7-33Save As User DefaultsTo set this feature, select Save as User Defaults from the Exit menu and press <En-ter>. This enables th

7-34SuperWorkstation 5038A-IL User's ManualNotes

Appendix A: POST Error Beep CodesA-1Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the

A-2SuperWorkstation 5038A-IL User's ManualNotes

B-1Appendix B: System Specifi cationsAppendix B System Specifi cationsProcessorOne Intel E3-1200V3 series processor or 4th Generation Intel Core™ i7/i5/

SuperWorkstation 5038A-IL User's Manual1-4Figure 1-1. Intel C226 Chipset: System Block DiagramNote: This is a general block diagram. Please see

B-2SuperWorkstation 5038A-IL User's ManualServerboardX10SAEDimensions: 12" x 9.6" (305 x 244 mm)ChassisSC732D4F-500B Form Factor: mid t

B-3Appendix B: System Specifi cationsRegulatory ComplianceElectromagnetic Emissions: FCC Class B, EN 55022 Class B, EN 61000-3-2/-3-3, CISPR 22 Class B

B-4SuperWorkstation 5038A-IL User's Manual(continued from front)The products sold by Supermicro are not intended for and will not be used in life

1-5Chapter 1: Introduction1-4 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (408

SuperWorkstation 5038A-IL User's Manual1-6Notes

Chapter 2: Installation2-1Chapter 2 Installation2-1 OverviewThis chapter provides a quick setup checklist to get your SuperWorkstation 5038A-IL up and

2-2SuperWorkstation 5038A-IL User's ManualFigure 2-1. Removing the Chassis Side Covers131622152-3 Accessing the Inside of the SystemYou may nee

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThe control panel on the 5038A-IL has several LEDs and a power button. These LEDs

3-2SuperWorkstation 5038A-IL User's ManualHDDIndicates IDE channel activity on the SAS, SATA and/or DVD-ROM drive when fl ashing.NICIndicates netw

Chapter 3: System Interface3-3Overheat/Fan FailWhen this LED fl ashes, it indicates a chassis fan failure. When on continuously it indicates an overhea

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccur

3-4SuperWorkstation 5038A-IL User's ManualNotes

4-1Chapter 4: Warning Statements for AC SystemsChapter 4Standardized Warning Statements for AC Systems4-1 About Standardized Warning StatementsThe fo

4-2SuperWorkstation 5038A-IL User's ManualWarnung WICHTIGE SICHERHEITSHINWEISEDieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situa

4-3Warning Statements for AC Systems안전을 위한 주의사항경고!이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확

4-4SuperWorkstation 5038A-IL User's ManualInstallation Instructions Warning!Read the installation instructions before connecting the system to th

4-5Chapter 4: Warning Statements for AC SystemsCircuit Breaker Warning!This product relies on the building's installation for short-circuit (over

4-6SuperWorkstation 5038A-IL User's ManualPower Disconnection Warning 電源切断の警告システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセスするには、システムの電源はすべてのソースから切断され、電

4-7Chapter 4: Warning Statements for AC Systems¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico qu

4-8SuperWorkstation 5038A-IL User's ManualEquipment Installation機器の設置トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可されています。 Warning!Only trained and qual

4-9Chapter 4: Warning Statements for AC Systemsアクセス制限区域このユ ニットは、アクセス制限区域に設置されることを想定しています。アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いてのみ出入りが可能です。 Warning!Th

iiiPrefacePrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the insta

4-10SuperWorkstation 5038A-IL User's ManualBattery Handling Warning!There is the danger of explosion if the battery is replaced incorrectly. Repl

4-11Chapter 4: Warning Statements for AC SystemsWarnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur

4-12SuperWorkstation 5038A-IL User's ManualWarnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein t

4-13Chapter 4: Warning Statements for AC SystemsBackplane Voltageバックプレーンの電圧システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。修理する際には注意ください。警告当系统正在进行时，背板上有很危险的电压或能

4-14SuperWorkstation 5038A-IL User's ManualComply with Local and National Electrical Codes Warning!Installation of the equipment must comply with

4-15Chapter 4: Warning Statements for AC SystemsProduct Disposal Warning!Ultimate disposal of this product should be handled according to all national

4-16SuperWorkstation 5038A-IL User's ManualWaarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met

4-17Chapter 4: Warning Statements for AC SystemsWarnungDie Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halt

4-18SuperWorkstation 5038A-IL User's Manual Warning!When installing the product, use the provided or designated connection cables, power cables a

4-19Chapter 4: Warning Statements for AC SystemsAttention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné

SuperWorkstation 5038A-IL User's ManualivChapter 5: Advanced Serverboard SetupChapter 5 provides detailed information on the X10SAE serverboard,

4-20SuperWorkstation 5038A-IL User's ManualNotes

Chapter 5: Advanced Serverboard Setup5-1Chapter 5 Advanced Serverboard SetupThis chapter covers the steps required to connect the data and power cable

5-2SuperWorkstation 5038A-IL User's Manual5-2 Connecting CablesNow that the serverboard is installed, the next step is to connect the cables to t

Chapter 5: Advanced Serverboard Setup5-35-3 I/O PortsThe I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-2 below

5-4SuperWorkstation 5038A-IL User's Manual5-4 Processor and Heatsink InstallationWarning: When handling the processor package, avoid placing dir

Chapter 5: Advanced Serverboard Setup5-55. Align the CPU key, which is a semi-circle cutout, against the socket key, which is the notch below the gol

5-6SuperWorkstation 5038A-IL User's ManualThermal GreaseHeatsink FinsInstalling the Heatsink1. Locate the CPU Fan power connec-tor on the mother

Chapter 5: Advanced Serverboard Setup5-78. Repeat Step 7 to insert all four heatsink fasteners into the mounting holes.9. Once all four fasteners ar

5-8SuperWorkstation 5038A-IL User's Manual5-5 Installing Memory ModulesNote: Check the Supermicro web site for recommended memory modules.CAUTIO

Chapter 5: Advanced Serverboard Setup5-9Memory SupportThe X10SAE supports up to 32 GB of Unbuffered ECC/Non-ECC DDR3-1600/1066 MHz memory in four DIMM

vPrefaceNotes

5-10SuperWorkstation 5038A-IL User's Manual• For Microsoft Windows users: Microsoft implemented a design change in Windows XP with Service Pack 2

Chapter 5: Advanced Serverboard Setup5-115-6 Adding PCI Add-On CardsThe 5038A-IL can accommodate standard size add-on cards populated in all slots on

5-12SuperWorkstation 5038A-IL User's ManualFigure 5-4. X10SAE Layout5-7 Serverboard DetailsX10SAERev. 1.01AUDIO FPJPAC1JSPDIF_OUTCOM4COM1LV33JWOR

Chapter 5: Advanced Serverboard Setup5-13Connector Description1394_1/2 1394 Connectors 1/2Audio FP Front Panel Audio HeaderHD AUDIO High-Defi nition Au

5-14SuperWorkstation 5038A-IL User's ManualReset ConnectorThe reset header is located on pins 3 and 4 of JF1. Attach the reset switch on the comp

Chapter 5: Advanced Serverboard Setup5-15Overheat/Fan Fail LED (OH)Connect an LED to pins 7 and 8 of JF1 to provide advanced warning of chassis overhe

5-16SuperWorkstation 5038A-IL User's ManualFan HeadersThe X10SAE has fi ve fan headers (Fan 1-5), all of which are 4-pin fans. Although pins 1-3 o

Chapter 5: Advanced Serverboard Setup5-17SGPIO HeadersTwo SGPIO (Serial General Purpose Input/Output) headers are designated T-SGPIO1 and SGPIO2. Thes

5-18SuperWorkstation 5038A-IL User's ManualUniversal Serial Bus (USB)Four Universal Serial Bus 2.0 ports (0/1, 2/3) and two USB 3.0 ports (10/11)

Chapter 5: Advanced Serverboard Setup5-19DOM PWR Connector (JSD1)The Disk-On-Module (DOM) power connector, located at JSD1, provides 5V (Gen1/Gen) pow

viSuperWorkstation 5038A-IL User's ManualTable of ContentsChapter 1 Introduction1-1 Overview ...

5-20SuperWorkstation 5038A-IL User's ManualIEEE 1394_1/1394_2 Connectors1394_1 and 1394_2 provide IEEE 1394 connections on the mother-board. Conn

Chapter 5: Advanced Serverboard Setup5-215-9 Jumper SettingsExplanation of JumpersTo modify the operation of the serverboard, jumpers can be used to c

5-22SuperWorkstation 5038A-IL User's ManualGLANJumper SettingsJumper Setting Defi nition 1-2 Enabled (default)2-3 DisabledWatch Dog Enable/Di

Chapter 5: Advanced Serverboard Setup5-23PCI Slot_SMB EnableJumper Settings Jumper Setting Defi nition Short EnabledOpen (Default) DisabledPCI

5-24SuperWorkstation 5038A-IL User's Manual5-10 Onboard IndicatorsLAN1/2 LEDsThe Ethernet ports on the I/O back-plane each have two LEDs. On each

Chapter 5: Advanced Serverboard Setup5-255-12 Installing SoftwareThe Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.s

5-26SuperWorkstation 5038A-IL User's ManualSuperDoctor IIIThe SuperDoctor® III program is a web-based management tool that supports remote manage

Chapter 5: Advanced Serverboard Setup5-275-13 Onboard BatteryPlease handle used batteries carefully. Do not damage the battery in any way; a damaged b

5-28SuperWorkstation 5038A-IL User's ManualNotes

Chapter 6: Advanced Chassis Setup6-1Chapter 6 Advanced Chassis SetupThis chapter covers the steps required to install components and perform simple ma

viiTable of ContentsCircuit Breaker ... 4-5Power Disconne

6-2SuperWorkstation 5038A-IL User's Manual6-2 Accessing the Inside of the SystemThe SC732 features two removable side covers, allowing easy acce

Chapter 6: Advanced Chassis Setup6-3Figure 6-2. Rotating the Hard Drive Cage6-3 Rotating the Hard Drive CageIn order to access and install component

6-4SuperWorkstation 5038A-IL User's Manual6-4 Removing and Installing 3.5" Hard DrivesThe SC732 chassis must be powered-down before hard dr

Chapter 6: Advanced Chassis Setup6-56. If a hard drive is already present, remove it by carefully pulling the sides of the hard drive carrier outward

6-6SuperWorkstation 5038A-IL User's ManualFigure 6-5. Installing a Hard Drive Carrier into the Hard Drive Cage11119Optional Screw

Chapter 6: Advanced Chassis Setup6-7Figure 6-6. Removing a 2.5" Hard Drive1415Thumb Screw6-5 Removing and Installing 2.5" Hard DrivesAddin

6-8SuperWorkstation 5038A-IL User's ManualFigure 6-7. Installing 2.5" Hard Drives5. If a hard drive is already present, remove it by caref

Chapter 6: Advanced Chassis Setup6-96-6 Installing a 3.5" DeviceThe SC732D chassis has one 3.5" device slot, which supports an optional dev

6-10SuperWorkstation 5038A-IL User's Manual6-7 Installing System FansInstalling the Rear Exhaust Fan1. Disconnect all power to the chassis.2.

Chapter 6: Advanced Chassis Setup6-11Installing the Front Cooling Fan (Optional)1. Disconnect all power to the chassis.2. Insert the four rubber pin

viiiSuperWorkstation 5038A-IL User's ManualChapter 6 Advanced Chassis Setup6-1 Static-Sensitive Devices ...

6-12SuperWorkstation 5038A-IL User's Manual6-8 Installing the Front BezelFront Bezel Installation1. Insert the tabs on the front bezel into the

Chapter 6: Advanced Chassis Setup6-136-9 Power SupplyThe SC732 chassis includes a 500 Watt power supply. In the event that it becomes necessary to rep

6-14SuperWorkstation 5038A-IL User's ManualNotes

Chapter 7: BIOS7-1Chapter 7 BIOS 7-1 IntroductionThis chapter describes the AMI BIOS Setup Utility for the X10SAE. The ROM BIOS is stored in a Flash

7-2SuperWorkstation 5038A-IL User's ManualHow to Start the Setup UtilityNormally, the only visible Power-On Self-Test (POST) routine is the memor

Chapter 7: BIOS7-3The following Main menu items will display:System Time/System Date Use this option to change the system date and time. Highlight Sys

7-4SuperWorkstation 5038A-IL User's Manual7-3 Advanced Setup Confi gurationsUse the arrow keys to select Boot Setup and press <Enter> to a

Chapter 7: BIOS7-5Wait For 'F1' If ErrorThis feature forces the system to wait until the 'F1' key is pressed if an error oc-curs.

7-6SuperWorkstation 5038A-IL User's ManualCPU Confi gurationThe following CPU information will be displayed:• Type of CPU• CPU Signature• Microco

Chapter 7: BIOS7-7Clock Spread Spectrum If this feature is set to Enabled, the BIOS will monitor the level of Electromagnetic Interference caused by t

Chapter 1 Introduction1-1 OverviewThe 5038A-IL is a high-end workstation comprised of two main subsystems: the SC732D4F-500B tower chassis and the X10

7-8SuperWorkstation 5038A-IL User's ManualNote: If there is any change to this setting, you will need to reboot the system for the change to take

Chapter 7: BIOS7-9DDR Power Limit2 (Available when "Turbo Mode" is set to Enabled)Use this feature to set the power limit for DDR2. Use the

7-10SuperWorkstation 5038A-IL User's ManualEnhanced C1E State (Available when "CPU C-States" is set to Enabled)Select Enabled to enable

Chapter 7: BIOS7-11C-State Pre-WakeSelect Enabled to support C State Pre-Wake State features. The options are Enabled and DisabledPackage C-State limi

7-12SuperWorkstation 5038A-IL User's ManualPrimary DisplayUse this feature to select the graphics device to be used as the primary display. You c

Chapter 7: BIOS7-13PCI-E Confi gurationThis item displays the information of the (graphics) device installed on a PCI-E slot.SLOT6 PCI-E 3.0 x16SLOT6

7-14SuperWorkstation 5038A-IL User's ManualSLOT3 PCI-E 2.0 x 1 ASPM/SLOT5 PCI-E 2.0 x 1 ASPM/SLOT7 PCI-E 2.0 x 1 ASPMThis feature confi gures t

Chapter 7: BIOS7-15Memory Frequency LimiterThis feature sets the limit of memory frequency for DIMM modules installed on the the motherboard. The opti

7-16SuperWorkstation 5038A-IL User's ManualPort 60/64 EmulationThis feature enables or disables I/O port 60h/64h emulation support. This should

Chapter 7: BIOS7-17SATA Confi gurationWhen this submenu is selected, the AMI BIOS automatically detects the presence of the SATA Devices and displays