Supermicro 5017C-TF Manuel d'utilisateur

SUPERSERVER 5017C-TF SUPER®USER’S MANUAL1.0

1-2SUPERSERVER 5017C-TF User's Manual1-2 Motherboard FeaturesAt the heart of the SuperServer 5017C-TF lies the X9SCM-F, a single processor mother

1-3Chapter 1: Introduction1-3 Server Chassis FeaturesThe following is a general outline of the main features of the SC811TQ-350B chassis.System Power

1-4SUPERSERVER 5017C-TF User's ManualFigure 1-1. Intel C204 Chipset: System Block DiagramNote: This is a general block diagram. Please see Chapt

1-5Chapter 1: Introduction1-4 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (40

1-6SUPERSERVER 5017C-TF User's ManualNotes

Chapter 2: Server Installation2-1Chapter 2 Server Installation2-1 OverviewThis chapter provides a quick setup checklist to get your SuperServer 5017C-

2-2SUPERSERVER 5017C-TF User's Manual!!Warnings and Precautions!installation only in a Restricted Access Location (dedicated equipment rooms, ser

Chapter 2: Server Installation2-3Always keep the rack's front door and all panels and components on the servers • closed when not servicing to ma

2-4SUPERSERVER 5017C-TF User's ManualFigure 2-1. Identifying the Sections of the Rack RailsAB2-4 Installing the System into a RackThis section

Chapter 2: Server Installation2-5Installing the Chassis RailsPosition the fi xed chassis rail sections you just removed along the side of the chassis m

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccur

2-6SUPERSERVER 5017C-TF User's ManualFigure 2-3. Installing the Server into a RackInstalling the Server Into the RackYou should now have rails a

Chapter 2: Server Installation2-7Installing the Server into a Telco RackIf you are installing the SuperServer 5017C-TF into a Telco type rack, follow

2-8SUPERSERVER 5017C-TF User's Manual2-5 Checking the Serverboard SetupAfter you install the 5017C-TF in the rack, you will need to open the uni

Chapter 2: Server Installation2-92-6 Checking the Drive Bay SetupNext, you should check to make sure the peripheral drives and the SATA drives have b

2-10SUPERSERVER 5017C-TF User's ManualNotes

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThere are several LEDs on the control panel as well as others on the SATA drive ca

3-2SUPERSERVER 5017C-TF User's Manual3-3 Control Panel LEDsThe control panel located on the front of the chassis has fi ve LEDs. These LEDs provi

Chapter 3: System Interface3-3HDDChannel activity for all HDDs. This light indicates DVD-ROM and/or SATA drive activity when fl ashing.PowerIndicates p

3-4SUPERSERVER 5017C-TF User's ManualNotes

Chapter 4: System Safety4-1Chapter 4 System Safety4-1 Electrical Safety Precautions!Basic electrical safety precautions should be followed to protect

iiiPrefacePrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the insta

SUPERSERVER 5017C-TF User's Manual4-24-2 General Safety PrecautionsFollow these rules to ensure general safety:Keep the area around the 5017C-TF

Chapter 4: System Safety4-34-3 ESD PrecautionsElectrostatic discharge (ESD) is generated by two objects with different electrical charges coming into

SUPERSERVER 5017C-TF User's Manual4-44-4 Operating PrecautionsCare must be taken to assure that the chassis cover is in place when the 5017C-TF i

Chapter 5: Advanced Motherboard Setup5-1Chapter 5 Advanced Motherboard SetupThis chapter covers the steps required to install processors and heatsinks

5-2SUPERSERVER 5017C-TF User's Manual5-2 Processor and Heatsink InstallationNotes: Always connect the power cord last and always remove it befor

Chapter 5: Advanced Motherboard Setup5-3Use your thumb and your index fi nger to hold the CPU at the top center edge 3. and the bottom center edge of t

5-4SUPERSERVER 5017C-TF User's ManualCPU properly installedLoad lever locked into place.Warning: The CPU will only seat inside the socket in one

Chapter 5: Advanced Motherboard Setup5-5Figure 5-3. Installing the HeatsinkOnce the CPU is loose, remove the it from the CPU socket.3. Clean the surfa

5-6SUPERSERVER 5017C-TF User's Manual5-3 Connecting CablesNow that the processors are installed, the next step is to connect the cables to the mo

Chapter 5: Advanced Motherboard Setup5-7Figure 5-1. Front Control Panel Header Pins (JF1)All JF1 wires have been bundled into single keyed ribbon cabl

SUPERSERVER 5017C-TF User's ManualivChapter 4: System SafetyYou should thoroughly familiarize yourself with this chapter for a general overview

5-8SUPERSERVER 5017C-TF User's Manual5-5 Installing MemoryNote: Check the Supermicro web site for recommended memory modules.CAUTIONExercise extr

Chapter 5: Advanced Motherboard Setup5-9Note: Due to memory allocation to system devices, the amount of memory that remains available for operational

5-10SUPERSERVER 5017C-TF User's Manual5-6 Adding PCI CardsPCI Expansion SlotsOne riser card is used to support a PCI expansion (add-on) card in

Chapter 5: Advanced Motherboard Setup5-11Figure 5-4. SUPER X9SCM-F Layout5-7 Motherboard DetailsJ31JTPMJ29JL1JI2C2JI2C1T-SGPIO1JWF1JPW2JWOLJSPKJPI2CJ

5-12SUPERSERVER 5017C-TF User's ManualLED IndicatorsNumber LED Description14 LE7 IPMI Heartbeat LED (IPMI Active)28 LE2 Onboard Standby PWR LEDHe

Chapter 5: Advanced Motherboard Setup5-135-8 Connector Defi nitions ATX Power Connector A 24-pin main power connector is located at JPW1. This power co

5-14SUPERSERVER 5017C-TF User's ManualNIC1/NIC2 (LAN1/LAN2)The NIC (Network Interface Controller) LED connection for LAN port 1 is located on pin

Chapter 5: Advanced Motherboard Setup5-15Universal Serial Bus (USB)Two Universal Serial Bus ports (USB 0/1) are located on the I/O backpanel and an ad

5-16SUPERSERVER 5017C-TF User's ManualFan HeaderPin Defi nitions Pin# Defi nition 1 Ground (Black)2 2.5A/+12V (Red)3 Tachometer4 PWM_Contro

Chapter 5: Advanced Motherboard Setup5-17Power Supply I2C ConnectorThe Power Supply (I2C) connector is located at JPI2C on the motherboard. This conne

vPrefaceNotes

5-18SUPERSERVER 5017C-TF User's ManualDOM PWR ConnectorA Disk On Module (DOM) Power Con-nector is located at JWF1. This connec-tor is used to pro

Chapter 5: Advanced Motherboard Setup5-195-9 Jumper SettingsExplanation of JumpersTo modify the operation of the mother-board, jumpers can be used to

5-20SUPERSERVER 5017C-TF User's ManualLAN Port Enable/DisableUse JPL1/JPL2 to enable or disable LAN Ports 1 and 2 on the motherboard. See the tab

Chapter 5: Advanced Motherboard Setup5-215-10 Onboard IndicatorsLAN1/LAN2 LEDsThe Ethernet ports (located beside the VGA port) have two LEDs. On each

5-22SUPERSERVER 5017C-TF User's Manual5-11 SATA Drive ConnectionsSATA PortsSix Serial ATA (SATA) ports (I-SATA 0~5) are located on the motherboa

Chapter 5: Advanced Motherboard Setup5-235-12 Installing DriversAfter all the hardware and operating system have been installed, you need to install c

5-24SUPERSERVER 5017C-TF User's ManualSupero Doctor IIIThe Supero Doctor III program is a Web base management tool that supports remote managemen

Chapter 5: Advanced Motherboard Setup5-25Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp://ftp.supermicro.com/utility/S

5-26SUPERSERVER 5017C-TF User's ManualNotes

Chapter 6: Advanced Chassis Setup6-1Chapter 6 Advanced Chassis SetupThis chapter covers the steps required to install components and perform mainte-na

viTable of ContentsChapter 1 Introduction1-1 Overview ...

6-2SUPERSERVER 5017C-TF User's ManualFigure 6-2. Chassis Rear View6-2 Control PanelThe control panel (located on the front of the chassis) must

Chapter 6: Advanced Chassis Setup6-36-3 System FansTwo 10-cm blower fans provide the cooling for the SuperServer 5017C-TF. The chassis includes air se

6-4SUPERSERVER 5017C-TF User's Manual6-4 Drive Bay Installation/RemovalAccessing the Drive BaysSerial ATA Drives: Because of their hotswap capab

Chapter 6: Advanced Chassis Setup6-5Figure 6-4. Mounting a Drive in a CarrierFigure 6-3. Removing a Drive Carrier

6-6SUPERSERVER 5017C-TF User's ManualSerial ATA Power CablesSATA power cables should be routed so that they do not block the airfl ow through the

Chapter 6: Advanced Chassis Setup6-76-5 Power SupplyThe 5017C-TF has a single 350 watt power supply. This power supply has the capability of operating

6-8SUPERSERVER 5017C-TF User's ManualNotes

Chapter 7: BIOS7-1Chapter 7 BIOS 7-1 IntroductionThis chapter describes the AMI BIOS Setup Utility for the X9SCM-F. The AMI ROM BIOS is stored in a Fl

7-2SUPERSERVER 5017C-TF User's ManualHow to Start the Setup UtilityNormally, the only visible Power-On Self-Test (POST) routine is the memory tes

Chapter 7: BIOS7-3System Overview: The following BIOS information will be displayed:System Time/System Date Use this option to change the system time

viiTable of ContentsChapter 3 System Interface3-1 Overview ...

7-4SUPERSERVER 5017C-TF User's Manual7-3 Advanced Setup Confi gurationsUse the arrow keys to select Boot Setup and hit <Enter> to access t

Chapter 7: BIOS7-519 at boot and allow the drives that are attached to these host adaptors to function as bootable disks. If this item is set to Disab

7-6SUPERSERVER 5017C-TF User's ManualAdjacent Cache Line Prefetch (Available when supported by the CPU)The CPU fetches the cache line for 64 byte

Chapter 7: BIOS7-7P-STATE CoordinationThis feature selects the type of coordination for the P-State of the processor. P-State is a processor operatio

7-8SUPERSERVER 5017C-TF User's ManualXNorth Bridge Confi gurationThis item displays the current North Bridge Revision.VT-dSelect Enabled to enable

Chapter 7: BIOS7-9Wake on LAN from S5Select Enabled to enable the capabiltiy to 'wake-up' the system from the S5 power state (Soft Off State

7-10SUPERSERVER 5017C-TF User's ManualAggressive Link Power ManagementThis feature Enables or Disables Agressive Link Power Management support fo

Chapter 7: BIOS7-11PCI Latency TimerThis feature sets the latency Timer of each PCI device installed on a PCI bus. Select 64 to set the PCI latency to

7-12SUPERSERVER 5017C-TF User's ManualSerial Port 2 ModeUse this feature to confi gure Serial Port 2 mode. The options are Normal, IrDA and ASK IR

Chapter 7: BIOS7-13Parity: None, Even, Odd, Mark, or SpaceStop Bits: 1 or 2XHardware Health Confi gurationFan Speed Control ModeThis feature allows the

viii5-12 Installing Drivers ... 5-23Supero Doctor III ...

7-14SUPERSERVER 5017C-TF User's ManualHigh – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Temperature Tolerance’ has

Chapter 7: BIOS7-157-4 Event LogsSmbios Event LogChange this item to enable or disable all features of the Smbios Event Logging during boot. The opti

7-16SUPERSERVER 5017C-TF User's Manual7-5 IPMI Confi gurationIntelligent Platform Management Interface (IPMI) is a set of common interfaces that I

Chapter 7: BIOS7-17SEL Components - Change this item to enable or disable all features of System Event Logging. The options are Enabled and Disabled.

7-18SUPERSERVER 5017C-TF User's Manual7-6 Boot SettingsUse this feature to confi gure Boot Settings:XBoot Options PriorityThis feature allows the

Chapter 7: BIOS7-197-7 Security SettingsIf the Administrator password is defi ned ONLY - this controls access to the • BIOS setup ONLY.If the User&apos

7-20SUPERSERVER 5017C-TF User's Manual7-8 Exit OptionsSelect the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup screen.

Chapter 7: BIOS7-21Save As User DefaultsTo set this feature, select Save as User Defaults from the Exit menu and press <En-ter>. This enables th

7-22SUPERSERVER 5017C-TF User's ManualNotes

Appendix A: POST Error Beep CodesA-1Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the

Chapter 1 Introduction1-1 OverviewThe SuperServer 5017C-TF is a high-end server comprised of two main subsys-tems: the SC811TQ-350B 1U server chassis

A-2SUPERSERVER 5017C-TF User's ManualNotes

B-1Appendix B: System Specifi cationsAppendix B System Specifi cationsProcessors Single Intel® Xeon® E3-1200 Series processor or a CoreTM i3-2100

B-2SUPERSERVER 5017C-TF User's ManualChassis SC811TQ-350B (1U Rackmount) Dimensions: (WxHxD) 17.2 x 1.7 x 22.6 in. (437 x 43 x 574 mm)W

B-3Appendix B: System Specifi cationsCalifornia Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only

B-4SUPERSERVER 5017C-TF User's ManualNotes