Supermicro SYS-6028R-T Manuel d'utilisateur télécharger pdf (Page 80)

6-6

SUPERSERVER 6028R-T/TT User's Manual

Figure 6-4. Removing SATA Drives

Installing/Removing Hot-swap SATA Drives

1. Push the release button on the drive carrier.

2. Swing the handle fully out and use it to pull the drive carrier straight out (see

Figure 6-4).

Note: Your operating system must have RAID support to enable the hot-plug ca-

pability of the drives.

Caution: All of the SATA drive carriers must remain in the drive bay to maintain proper

cooling airow.

Release Button

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 127 128

SUPER 1
Manual Revision 1.0 2
Release Date: August 7, 2014 2
About This Manual 3
Manual Organization 3
Table of Contents 6
Chapter 1 9
Introduction 9
1-2 Serverboard Features 10
1-3 Server Chassis Features 11
FRONT PANEL 12
SYSTEM POWER 12
FAN SPEED 12
1-4 Contacting Supermicro 13
Chapter 2 15
Server Installation 15
2-4 Warnings and Precautions 16
Rack Mounting Considerations 17
SUPERSERVER 6028R-T/TT Manual 18
Installing the Chassis Rails 19
Installing the Rack Rails 19
Chapter 3 23
System Interface 23
3-3 Control Panel LEDs 24
3-4 Drive Carrier LEDs 25
Chapter 4 27
Installation Instructions 30
Circuit Breaker 31
Power Disconnection Warning 32
ילמשח קותינ ינפמ הרהזא 33
Equipment Installation 34
Restricted Area 35
Battery Handling 36
Redundant Power Supplies 38
Backplane Voltage 39
Product Disposal 41
Hot Swap Fan Warning 42
Power Cable and AC Adapter 44
(UL/CSA  ) 45
Chapter 5 47
Advanced Serverboard Setup 47
•Control Panel cable (JF1) 48
5-3 I/O Ports 49
OPEN 1st 50
WARNING! 50
Removing the Heatsink 53
Installing a CPU Heatsink 53
5-5 Installing Memory 54
5-6 Adding PCI Add-On Cards 56
X10DRi-(T) 57
5-8 Connector Denitions 60
USB 4, 6 65
Pin # Denition 65
Pin # Denition 65
5-9 Jumper Settings 66
X8DT3-LN4/LN4F 69
X8DT3/i-F/-LN4F 69
5-11 SATA Ports 70
5-12 Installing Software 71
SuperDoctor® 5 72
5-13 Onboard Battery 73
Chapter 6 75
Advanced Chassis Setup 75
Unpacking 76
6-2 Control Panel 77
6-3 System Fans 77
Accessing the Drive Bays 78
SATA Drive Installation 79
Release Button 80
DVD-ROM Drive Installation 82
6-5 Power Supply 83
Chapter 7 85
7-2 Main Setup 86
Boot Feature 88
Power Conguration 89
North Bridge 90
IIO Conguration 90
IIO0 Conguration 90
CPU Conguration 90
IIO1 Conguration 91
IOAT Conguration 92
Memory Conguration 94
•P1 DIMMA1 95
•P1 DIMMB1 95
• P1 DIMMC1 95
•P1 DIMMD1 95
•USB Conguration 96
•USB Module Version 96
•USB Devices 96
•Software Preserve Support 101
•ME Firmware Status #2 103
•Current State 103
•Error Code 103
•PCI Bus Driver Version 103
•PCI Latency Timer 103
Super IO Conguration 105
Console Redirection Settings 106
ACPI Settings 112
iSCSI Conguration 112
Add an Attempt 112
Delete Attempts 112
Change Attempt Order 112
7-4 Event Logs 113
7-5 IPMI 115
BMC Network Conguration 116
7-6 Security Settings 118
7-7 Boot Settings 119
7-8 Save & Exit 121
Appendix A 123
BIOS Error Beep Codes 123
Appendix B 125
System Specications 125

Commentaires sur ces manuels

Pas de commentaire

Supermicro SYS-6028R-T Manuel d'utilisateur Page 80

Commentaires sur ces manuels

Produits connexes et manuels pour Le serveur à l'état brut Supermicro SYS-6028R-T