Supermicro 2016Ti-HTRF Manuel d'utilisateur télécharger pdf (Page 69)

Chapter 6: Advanced Chassis Setup

6-5

Installing/Removing Hot-swap Drives

To remove a carrier, push the release button located beside the drive LEDs.1.

Swing the handle fully out and use it to pull the unit straight out (see Figure 2.

6-4).

Be aware that powering down a node will power down all the hard drives

that are logically associated with it (as shown in Figure 6-6).

Figure 6-3. Mounting a Hard Drive in a Carrier

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 105 106

SUPER 1
About This Manual 3
Manual Organization 3
Table of Contents 6
Chapter 3 System Interface 7
Chapter 4 System Safety 7
Chapter 1 9
Introduction 9
1-2 Motherboard Features 10
RoHS 6/6 11
1-3 Server Chassis Features 12
: System Notes 13
1-4 2U Twin 13
1-5 Contacting Supermicro 14
Chapter 2 15
Server Installation 15
Warnings and Precautions! 16
Rack Mounting Considerations 17
Removing the Protective Film 18
Standard Chassis Installation 22
2-6 Preparing to Power On 24
Chapter 3 27
System Interface 27
3-3 Control Panel LEDs 28
3-4 Drive Carrier LEDs 29
Chapter 4 31
System Safety 31
4-3 ESD Precautions 33
LITHIUM BATTERY 34
BATTERY HOLDER 34
Chapter 5 35
Advanced Motherboard Setup 35
5-2 Motherboard Installation 36
5-3 Connecting Cables 37
5-4 Rear I/O Ports 38
Removing the Heatsink 42
5-6 Installing Memory 43
Memory Support 44
Memory Population Guidelines 45
Press Down 46
5-8 Motherboard Details 48
BAR CODE 49
5-9 Connector Deﬁ nitions 51
5-10 Jumper Settings 57
5-11 Onboard Indicators 60
5-12 SATA Ports 61
5-13 Installing Software 62
Supero Doctor III 63
Chapter 6 65
Advanced Chassis Setup 65
6-2 Control Panel 66
6-3 System Fans 66
Fan Conﬁ guration 67
System Fan Failure 67
Overview 68
6-5 Node Installation/Removal 71
6-7 Power Supply 73
Release Tab 74
Chapter 7 75
7-2 Main Setup 76
XBOOT Feature 78
Processor & Clock Options 80
Advanced Chipset Control 82
SATA Conﬁ guration 82
XPCI/PnP Conﬁ guration 85
XRemote Access Conﬁ guration 86
Hardware Health Conﬁ guration 87
XACPI Conﬁ guration 90
XIPMI Conﬁ guration 91
XEvent Log Conﬁ guration 92
Chapter 7: BIOS 93
PCIE Error Log 93
The options are Yes and No 93
7-4 Security Settings 94
7-5 Boot Settings 95
7-6 Exit Options 96
Appendix A 99
POST Error Beep Codes 99
Appendix B 101
BIOS Recovery 101
Appendix C 103
System Speciﬁ cations 103

Commentaires sur ces manuels

Pas de commentaire

Supermicro 2016Ti-HTRF Manuel d'utilisateur Page 69

Commentaires sur ces manuels

Produits connexes et manuels pour Le serveur à l'état brut Supermicro 2016Ti-HTRF