Supermicro SYS-7047A-T Manuel d'utilisateur Page 11
- Page / 110
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1-3
Chapter 1: Introduction
socket is empty the PCI slos associated with it cannot be used. See Chapter 5 for
details.
Onboard Controllers/Ports
The color-coded I/O ports include one COM port, six USB 2.0 ports, PS/2 mouse and
keyboard ports, two Gb Ethernet ports and six HDA (High Defi nition Audio) ports.
1-3 Chassis Features
The SC743TQ-1200B-SQ is an ATX form factor chassis that can be used as a tower
or mounted in a 4U rackmount confi guration. The following is a general outline of
the main features of the SC743TQ-1200B-SQ chassis.
System Power
The 7047A-73/7047A-T features a single 1200W power supply. This power supply
unit has been designed to operate at a low noise level to make it ideal for use in
a workstation environment.
SAS Subsystem
The SC743TQ-1200B-SQ chassis was designed to support eight SAS or SATA hard
drives, which are hot-swappable units. (SAS is with 7047A-73 only).
Front Control Panel
The control panel on the SuperWorkstation 7047A-73/7047A-T provides you with
system monitoring and control. LEDs indicate system power, HDD activity, network
activity, overheat conditions and power supply failure. A main power button and a
system reset button are also included.
Note: the power supply fail LED indicates the power supply fan has failed.
Cooling System
The SC743TQ-1200B-SQ chassis has an innovative "Super Quiet" cooling design
that provides suffi cient cooling at very low noise level - ideal for a workplace envi-
ronment. The chassis includes two 8-cm hot-plug PWM (Pulse Width Modulation)
system cooling fans located in the middle of the chassis. A 9-cm PWM exhaust fan
is also located at the rear of the chassis.
The power supply has two fans for redundancy; if one fan fails the other will incease
its rpm to compensate. This may cause the system to run louder than usual. See
details in Chapter 6.
- SUPER 1
- Manual Revision 1.0a 2
- Release Date: August 17, 2012 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- • SAS/SATA Accessories 9
- • Optional: 9
- 1-2 Serverboard Features 10
- 1-3 Chassis Features 11
- System Block Diagram 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- Installation 15
- Warnings and Precautions! 16
- Rack Mounting Considerations 17
- Inner rail 18
- Outer rail 18
- Rail brackets 18
- Installing the Chassis Rails 19
- Installing the Rack Rails 20
- Chapter 3 23
- System Interface 23
- 3-3 Control Panel LEDs 24
- 3-4 Drive Carrier LEDs 25
- Chapter 4 27
- System Safety 27
- 4-3 ESD Precautions 29
- TUM ATT 30
- ATT O 30
- Chapter 5 31
- Advanced Serverboard Setup 31
- 5-2 Serverboard Installation 32
- • Control Panel cable (JF1) 33
- 5-4 I/O Ports 34
- Press down on 35
- 'Close 1st' 35
- Pull lever away 35
- WARNING! 36
- OPEN 1st 37
- Installing a CPU Heatsink 38
- Removing the Heatsink 39
- Memory Support 41
- UDIMM Memory Support 42
- RDIMM Memory Support 42
- 5-7 Adding PCI Add-On Cards 45
- 5-8 Serverboard Details 46
- Figure 5-4b. X9DAi Layout 47
- X9DA7/X9DAi Quick Reference 48
- 5-9 Connector Defi nitions 50
- 5-10 Jumper Settings 56
- 5-11 Onboard Indicators 59
- 5-12 SAS and SATA Ports 60
- 5-13 Installing Software 61
- SuperDoctor III 62
- Chapter 6 65
- Advanced Chassis Setup 65
- 8 SAS/SATA Drive Bays 66
- (behind locking bezel) 66
- System ResetMain Power 66
- 5.25" Drive Bays (2) 66
- USB Ports 66
- 6-2 Front Control Panel 67
- 6-3 System Fans 68
- 6-4 Drive Bay Installation 70
- SAS/SATA Backplane 71
- 6-5 Power Supply 73
- Chapter 7 75
- 7-2 Main Setup 76
- XBoot Features 78
- • Type of CPU 79
- • CPU Signature 79
- • Microcode Patch 79
- • CPU Stepping 79
- • Maximum CPU Speed 79
- XChipset Confi guration 84
- XNorth Bridge 84
- XIOH Confi guration 84
- XQPI Confi guration 85
- XDIMM Confi guration 86
- XDIMM Information 86
- XSouth Bridge Confi guration 88
- Audio Confi guration 89
- XSATA Confi guration 90
- XSCU Confi guration 91
- XPCIe/PCI/PnP Confi guration 91
- Super IO Confi guration 93
- Serial Port 0 Confi guration 93
- XConsole Redirection Settings 93
- Console Redirection Settings 95
- XACPI Setting 97
- 7-3 Event Logs 99
- 7-4 Boot 101
- 7-6 Security 102
- 7-7 Save & Exit 103
- Appendix A 105
- BIOS Error Beep Codes 105
- Appendix B 107
- System Specifi cations 107
Produits connexes et manuels pour Le serveur à l'état brut Supermicro SYS-7047A-T
(120 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels