Supermicro SYS-5038A-IL Manuel d'utilisateur Page 54
- Page / 122
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-14
SuperWorkstation 5038A-IL User's Manual
Reset Connector
The reset header is located on pins 3
and 4 of JF1. Attach the reset switch
on the computer chassis to these
pins. See the table on the right for
pin defi nitions.
Power Button
The connection for the power button
is on pins 1 and 2 of JF1. The chas-
sis power button should be connected
here. This button can also function
as a suspend button (BIOS setting).
See the table on the right for pin
defi nitions.
5-8 Connector Defi nitions
Main ATX Power Connector
Pin Defi nitions
Pin# Defi nition Pin # Defi nition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
Reset Button
Pin Defi nitions (JF1)
Pin# Defi nition
3 Reset
4 Ground
Power Button
Pin Defi nitions (JF1)
Pin# Defi nition
1 Signal
2 +3V Standby
Main ATX Power Supply
Connector
A 24-pin main power supply connec-
tor (JPW1) and an 8-pin CPU power
connectors (JPW2) are located on the
serverboard. These power connectors
meet the SSI EPS 12V specifi cation.
These power connectors must be con-
nected to your power supply. See the
table on the right for pin defi nitions.
Required Connection
Processor Power Connector
Pin Defi nitions
Pins Defi nition
1 - 4 Ground
5 - 8 +12V
Processor Power Connectors
JPW2 must also be connected to the
power supply to provide power for the
processors. See the table on the right
for pin defi nitions.
Warning: To prevent damage to the power supply or serverboard, please use a
power supply that contains a 24-pin and two 8-pin power connectors. Be sure to
connect these to the 24-pin and the two 8-pin power connectors on your serverboard
to supply adequate power to your system. Failure to do so will void the manufacturer
warranty on the power supply and serverboard.
- SUPER 1
- Manual Revision 1.0 2
- Release Date: June 14, 2013 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Chassis Features 11
- System Block Diagram 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- Installation 15
- • Two USB 3.0 ports 17
- • Two USB 2.0 ports 17
- • Two IEEE 1394A ports 17
- • One audio port 17
- • One microphone port 17
- 3-4 Control Panel LEDs 18
- Overheat/Fan Fail 19
- Chapter 4 21
- ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ 23
- Installation Instructions 24
- 250 V, 20 A 25
- Power Disconnection Warning 26
- ילמשח קותינ ינפמ הרהזא 27
- Equipment Installation 28
- Restricted Area 29
- Battery Handling 30
- Redundant Power Supplies 32
- Backplane Voltage 33
- Product Disposal 35
- רצומה קוליס 36
- Power Cable and AC Adapter 38
- (UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ ) 39
- Chapter 5 41
- Advanced Serverboard Setup 41
- • Control Panel cable (JF1) 42
- 5-3 I/O Ports 43
- CPU Pin 1 45
- Installing the Heatsink 46
- Removing the Heatsink 47
- Memory Population Guidelines 49
- 5-6 Adding PCI Add-On Cards 51
- Rev. 1.01 52
- USB3.0 14/15 52
- A-SATA0 (3.0) 52
- A-SATA1 (3.0) 52
- 5-8 Connector Defi nitions 54
- (NC: No Connection) 57
- 5-9 Jumper Settings 61
- 5-10 Onboard Indicators 64
- 5-11 SATA Ports 64
- 5-12 Installing Software 65
- SuperDoctor III 66
- 5-13 Onboard Battery 67
- Chapter 6 69
- Advanced Chassis Setup 69
- Release Tab (A) 71
- HDD Cage (B) 71
- Release Tabs 72
- Optional 74
- Thumb Screw 75
- Rail (A) 77
- Cover Plate 77
- 6-7 Installing System Fans 78
- 6-9 Power Supply 81
- Chapter 7 83
- 7-2 Main Setup 84
- Boot Feature 86
- Power Confi guration 87
- CPU Confi guration 88
- • System Agent Bridge Name 93
- • VT-d Capability 93
- • IGFX VBIOS Version 93
- • IGfx Frequency 93
- PCI-E Confi guration 95
- Memory Confi guration 96
- • Intel PCH Rev ID 97
- • USB Confi guration 97
- • USB Devices 97
- On Board Chip Confi guration 98
- • Software Preserve Support 100
- ACPI Settings 102
- • ME FW Version 103
- • ME Firmware Mode 103
- • ME Firmware Type 103
- • ME Firmware SKU 103
- • PTT Capability /State 103
- Firmware Update Confi guration 104
- Super IO Confi guration 104
- H/W (Hardware) Monitor 105
- Console Redirection Settings 106
- 7-4 Event Logs 109
- View SMBIOS Event Log 110
- 7-5 Boot Settings 111
- 7-6 Security Settings 113
- 7-7 Save & Exit 114
- Appendix A 117
- BIOS Error Beep Codes 117
- Appendix B 119
- System Specifi cations 119
- Regulatory Compliance 121
© 2020, manymanuals.fr. Tous droits réservés | 0.533 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels